Mewant Hand Stitch Car Steering Wheel Cover Review: Tesla Model 3 and Model Y

A worn steering wheel feels rough under your hands, and a new wheel costs far more than a cover. A Mewant hand stitch car steering wheel cover is the middle path: a piece of leather cut to the shape of your exact wheel, stitched on by hand over the original leather, until it feels like a new wheel. It is not a slip-on cover. You sew it on yourself, stitch by stitch, and the result fits the wheel like it was made there, cut for your model.

The short answer: a Mewant hand stitch car steering wheel cover is cut for one wheel, so if you drive a Tesla Model 3 or Model Y, start with the Mewant Tesla cover — it is cut for those two wheels and takes around 1.5 to 2.5 hours of stitching. If you drive a Jeep Wrangler JK, the Mewant Jeep cover is the same idea cut for that wheel. And if your wheel is none of those, a universal stitch-on cover fits by diameter instead of by model. All three are below, and none of them fits every wheel — check your model or your diameter before you order.

As an Amazon Associate I earn from qualifying purchases.

Quick Pick: Mewant Hand Stitch Car Steering Wheel Covers

Mewant Tesla Model 3 and Model Y Cover: The Hero Hand-Stitch Fit

The Mewant Tesla cover is the hero of this review, and it is the clearest example of what Mewant does. It is a hand-stitch black faux leather steering wheel cover made for the Tesla Model 3, model years 2017 to 2023, and the Tesla Model Y, model years 2020 to 2023. The colour is black faux leather with red and black thread, and the manufacturer part number is AMZ3-CARG1933012P120120221-US. The cover is cut from a template of the Tesla wheel, so it follows the shape of the spokes and the rim exactly, rather than stretching over the wheel like a universal cover. Our Tesla steering wheel cover review covers the wider set of Tesla covers — this review is about the Mewant hand-stitch one, and how it differs from a slip-on.

The stitching time is the honest number to plan around. The listing says you will need to sew the cover onto your steering wheel yourself with the installation tools, and that it takes around 1.5 to 2.5 hours. That is guidance from the listing, not a measured result — a first-timer working slowly should plan for the long end of that range. The tools come with the cover: needle, thread and the rest of the kit are included, so there is nothing else to buy before you start.

The Tesla cover is the pick in this roundup for the Tesla driver who wants the factory look back — the original wheel, re-skinned in black faux leather with red stitching, fitted by hand in an afternoon. It only fits the two Tesla models and model years named on the listing — Model 3 2017–2023 and Model Y 2020–2023, not later model years — and that is the point: a cover cut for one wheel fits that wheel properly, and no other.

MEWANT Hand Stitch Black Faux Leather Steering Wheel Cover for Tesla Model 3 Model Y on Amazon: hand-stitch faux leather cover, black with red and black thread, for Tesla Model 3 2017-2023 and Model Y 2020-2023, stitching around 1.5 to 2.5 hours per the listing, installation tools included, part number AMZ3-CARG1933012P120120221-US.

Buy the Mewant Tesla cover if: you drive a Tesla Model 3 from 2017 to 2023 or a Model Y from 2020 to 2023, and you are happy to spend an afternoon stitching. Check your model year against the listing first.

Mewant Jeep Wrangler JK Cover: The Hand-Stitch Leather Wrap

The Mewant Jeep cover is the same idea cut for a different wheel: a hand-stitched leather steering wheel wrap for the Jeep Wrangler JK, model years 2007 to 2010. The material is hive microfiber leather with red thread, and the model number is BAR2161095201. Like the Tesla cover, it is cut from a template of the Wrangler wheel, so it follows the shape of the rim and the spokes rather than stretching over them. Our Jeep steering wheel cover review covers the wider set of Jeep covers — the Mewant one is the hand-stitch option among them, for the driver who wants the cover to look like it came with the car.

One honest flag belongs here. The crawl of the Jeep listing showed no featured offers available at the time it was read, which means the listing may have no live offer right now, or the offer may simply not have shown in the crawl. The cover itself is a real Mewant listing with a real model number, and the link below still points at it — but check that the listing shows a live offer before you order, and do not assume it is in stock.

The Jeep cover is the pick in this roundup for the Wrangler JK driver with a worn wheel — a hand-stitched wrap that restores the grip and the look of the original, in an afternoon of stitching. It fits only the Wrangler JK from 2007 to 2010, so check your model year before you order, and check the offer as well.

MEWANT Steering Wheel Cover for Jeep Wrangler (JK) 2007-2010 Hand-Stitched Leather Steering Wheel Wrap on Amazon: hand-stitched leather wrap, hive microfiber leather with red thread, for Jeep Wrangler JK 2007-2010, model BAR2161095201. No featured offers showed in the crawl — check the live offer before ordering.

Buy the Mewant Jeep cover if: you drive a Jeep Wrangler JK from 2007 to 2010 and want a hand-stitched wrap in microfiber leather. Confirm the listing shows a live offer first.

Belinous Universal Cover: The Stitch-On Cover for Any Wheel Size

The Belinous cover is the universal option in this roundup, and it works the other way round from the Mewant covers: instead of being cut for one model, it is sized by diameter. It is a lace-up, stitch-on steering wheel wrap made from a whole piece of cowhide, size XS5 in black, model SC01, and it fits wheels from 13 to 20 inches in diameter. That range covers most cars, trucks and pickups, and it fits both round wheels and D-shaped wheels, according to the listing. The cover comes with a needle and thread, and you lace it on yourself, the same way as the Mewant covers.

A universal cover is a trade-off. It will never follow the spokes of your wheel as closely as a cover cut from a template of your model, because it does not know your model — it only knows your diameter. What it gives you in return is choice: any wheel in the 13 to 20 inch range, any car, without waiting for a model-specific listing. Measure your wheel across the middle, spoke to spoke, before you order, and pick the size that matches — a cover that is too large will slip, and one that is too small will not close.

The Belinous cover is the pick in this roundup for the driver whose car has no Mewant listing, or who wants a real cowhide cover rather than faux leather. It is the only cover here with a diameter range on the listing, and that range is the number to check: 13 to 20 inches, measured across your own wheel.

BELINOUS Leather Steering Wheel Cover Lace Up, Stitch on Steering Wheel Wrap, Universal Fit 13-20 Inch on Amazon: stitch-on leather wrap, whole piece of cowhide, size XS5 black, model SC01, universal fit 13 to 20 inches, round and D-shaped wheels, needle and thread included.

Buy the Belinous universal cover if: your car has no model-specific Mewant cover, or you want a real cowhide stitch-on cover sized by diameter. Measure your wheel across the middle first — it must fall inside 13 to 20 inches.

How Long Does Hand Stitching Take

Hand stitching takes time, and the honest answer is that it takes as long as it takes. The Mewant Tesla listing says around 1.5 to 2.5 hours, and the Mewant Silverado listing — a genuine leather cover for the Chevy Silverado that was checked during research — says about 1 to 2 hours. Those are two different numbers for two different covers, and they are both guidance, not measured results: nobody timed a stitch in this review, and your time will depend on your hands, your wheel and how careful you are.

Plan for the long end. Set aside an afternoon, work in good light, and take breaks rather than rushing the last quarter of the wheel — the stitches you rush are the stitches that show. The first half of the wheel goes slowly while you learn the pattern; the second half goes faster. If you have never sewn anything before, the Tesla cover’s 1.5 to 2.5 hour range is the right expectation, and finishing inside it is a good result, not a slow one.

Mewant Hand Stitch Car Steering Wheel Cover Sizes and Fitment

Fitment for a Mewant hand stitch car steering wheel cover is by model, not by size. The Tesla cover fits the Model 3 from 2017 to 2023 and the Model Y from 2020 to 2023, and nothing else. The Jeep cover fits the Wrangler JK from 2007 to 2010, and nothing else. That is the whole point of a Mewant cover: it is cut from a template of your exact wheel, so it follows the rim and the spokes, and a wheel it was not cut for will not fit it.

There are two more fitment rules on the listings. First, check whether your wheel is leather: the Silverado listing says its cover is only suitable for a leather steering wheel, and stitching needs leather to bite into — if your wheel is rubber or has mahogany wood, check the listing for your own model before ordering, because the cover may not fit. Second, the universal Belinous cover fits by diameter instead: 13 to 20 inches, measured across the middle of the wheel. If your car has no Mewant listing, measure the diameter and buy by that number — and if your wheel falls outside 13 to 20 inches, the universal cover will not fit either.

How to Stitch a Mewant Cover Onto Your Wheel

Stitching a Mewant cover onto your wheel takes patience more than skill, and the order matters. Start by laying the cover over the wheel and lining up the seams with the spokes, so the cover sits evenly before a single stitch goes in. Thread the needle with the thread from the kit, knot the end, and start at the top of the wheel, working your way around in small, even stitches. Pull each stitch snug, but not so tight that it puckers the leather — the cover should sit flat against the wheel, with no wrinkles and no loose edge.

Work in sections and check the fit as you go: after each quarter of the wheel, run your hands over the cover and look for wrinkles or slack. If the cover shifts, undo the last few stitches and re-seat it — it is easier to fix a quarter than to finish the whole wheel and find it twisted. Do not remove the steering wheel or the airbag: the cover is stitched on with the wheel in place. When you finish, knot the thread, tuck the end under the leather, and run your hands around the whole wheel — it should feel like one piece, with no loose edge anywhere.

Leather, Microfiber or Faux Leather: Choosing Your Material

The three covers in this roundup use three different materials, and the choice matters more than the colour. The Tesla cover is black faux leather: it looks like leather, cleans easily and costs less than the real thing, but it will not age the way leather does. The Jeep cover is hive microfiber leather: a textured microfiber with a patterned surface. The Belinous cover is a whole piece of cowhide: real leather, with the smell and the feel of it, that softens with use.

Our genuine leather steering wheel cover review covers the wider set of real leather covers, including how to tell genuine leather from faux. The short version is this: if you want the lowest maintenance, pick faux leather or microfiber; if you want the cover to age with the car and you are happy to condition it now and then, pick real leather. The stitching is the same either way — the material changes the feel and the care, not the fit.

Mewant Hand Stitch Car Steering Wheel Cover Mistakes to Avoid

The most common Mewant hand stitch car steering wheel cover mistake is ordering for the wrong model. A Tesla cover will not fit a Jeep wheel, and a Jeep cover will not fit a Tesla wheel — the covers are cut for one model, and the model year matters as much as the model. The second mistake is ordering for a rubber or wood wheel: the listings say the covers are only suitable for a leather steering wheel, and stitching into rubber or wood will not hold.

The third mistake is rushing the stitching. The stitches you rush are the stitches that show, and a cover stitched in a hurry looks stitched in a hurry — plan for the long end of the time range and take breaks. The fourth is pulling the thread too tight and puckering the leather, which leaves wrinkles that will not come out. The fifth is not checking the offer before ordering: the Jeep listing showed no featured offers in the crawl, and a listing with no offer cannot be bought at any price. And the sixth is removing the steering wheel to fit the cover — the cover is stitched on with the wheel in place, and the airbag stays where it is.

Who Should Buy a Mewant Hand Stitch Cover — and Who Should Not

Buy a Mewant hand stitch cover if: your steering wheel is worn, and your exact model has a Mewant listing. A hand-stitched cover restores the grip and the look of the original wheel for the cost of an afternoon, and it fits like it was made for the wheel — because it was.

Buy with care if: you have never sewn anything before, or your wheel is rubber or wood. The stitching is not hard, but it takes patience, and the listings say the covers are only suitable for a leather wheel. If your wheel is not leather, a slip-on cover is the better choice.

Do not buy a Mewant hand stitch cover if: your car has no Mewant listing and your wheel falls outside the 13 to 20 inch range of the universal cover, or you do not want to spend an afternoon stitching. A slip-on cover takes a minute to fit and needs no needle — the hand-stitch cover is for the driver who wants the factory look and is willing to sew for it.

The Verdict

The best Mewant hand stitch car steering wheel cover is the one cut for your wheel. The Mewant Tesla cover is the pick for the Tesla Model 3 and Model Y driver: a black faux leather cover with red stitching, cut for those two wheels, with around 1.5 to 2.5 hours of stitching ahead of you. The Mewant Jeep cover is the pick for the Wrangler JK driver: a microfiber leather wrap for the 2007 to 2010 wheel, with the same hand-stitch job and the same factory look at the end of it. And the Belinous universal cover is the pick for everyone else: a real cowhide stitch-on cover sized by diameter, 13 to 20 inches, for any wheel that falls inside that range.

Whichever cover you choose, check three things before you order: your exact model and model year against the listing, whether your wheel is leather, and whether the listing still shows a live offer — listings change, and a listing that showed an offer when this review was researched may not show one now. Measure the wheel, read the listing, and set aside the afternoon. For the wider set of covers beyond Mewant, our best steering wheel covers article covers the slip-on options as well as the stitch-on ones.

Frequently Asked Questions

How long does it take to stitch on a Mewant hand stitch car steering wheel cover?

The Mewant Tesla listing says around 1.5 to 2.5 hours, and the Mewant Silverado listing says about 1 to 2 hours — those are guidance from the listings, not measured results, and your time will depend on your hands and your wheel. Plan for the long end of the range, work in good light, and take breaks rather than rushing the last quarter of the wheel, because the stitches you rush are the stitches that show. A first-timer should set aside a whole afternoon.

Will a Mewant hand stitch car steering wheel cover fit my car?

Only if Mewant makes a cover for your exact model and model year. The Tesla cover fits the Model 3 from 2017 to 2023 and the Model Y from 2020 to 2023, and the Jeep cover fits the Wrangler JK from 2007 to 2010 — nothing else. A Mewant cover is cut from a template of one wheel, so it will not fit a different model. If your car has no Mewant listing, the universal Belinous cover fits by diameter instead: 13 to 20 inches, measured across the middle of your wheel.

Do I need to remove my steering wheel to fit a Mewant cover?

No — the cover is stitched onto the wheel with the wheel in place, and the airbag stays where it is. Lay the cover over the wheel, line up the seams with the spokes, and stitch your way around in small, even stitches, checking the fit after each quarter of the wheel. Do not remove the steering wheel or the airbag to fit the cover.

What is the difference between the Mewant Tesla cover and the universal Belinous cover?

The Mewant Tesla cover is cut from a template of the Tesla Model 3 and Model Y wheel, so it follows the rim and the spokes exactly, but it fits only those two models. The Belinous cover is a whole piece of cowhide sized by diameter, 13 to 20 inches, so it fits any wheel inside that range, but it will never follow your spokes as closely as a cover cut for your model. The Mewant cover is faux leather; the Belinous cover is real cowhide.

Can I stitch a Mewant cover over a rubber or wood steering wheel?

No — the Mewant listings say the covers are only suitable for a leather steering wheel. If your wheel is rubber or has mahogany wood, the cover will not fit, because the stitching needs leather to bite into. If your wheel is not leather, a slip-on cover is the better choice — it grips the wheel without stitching, and it does not need leather underneath.

How do I care for a hand-stitched leather steering wheel cover?

Wipe it down with a damp cloth when it gets dirty, and keep it out of harsh cleaners that dry leather out. A real leather cover, like the Belinous cowhide, benefits from a leather conditioner now and then, which keeps it soft and stops it cracking. A faux leather or microfiber cover, like the Mewant Tesla and Jeep covers, needs less care — a wipe-down is usually enough. Check the stitching now and then, and if a stitch comes loose, re-stitch that section before it unravels.